Boiler Receiver
tado° Wireless Receiver X Review

Controls zones | Thread border router | Hot water (UK) | Matter and Thread

Overview

The Wireless Receiver X is the unit that wires to your boiler in the wireless starter kit. tado’s shop page says it allows control of multiple zones independently, can replace an existing wireless receiver in zoning set-ups and acts as a Thread border router. It measures 156 x 96 mm, runs on 230 VAC, has no display and is controlled through the tado° app. The UK version has two buttons, for heating and for hot water, and works with system and combi boilers.

Ad: we earn commission if you buy through the price buttons on this page.

Check latest price

Subscription note: The tado° app works without a subscription. tado lists features such as Adaptive Heating, Geofencing and Open Window Detection under its optional AI Assist subscription, which you buy in the app and can cancel at any time.

Key Features

✓Controls multiple zones independently (boiler and heat pump zoning)
✓Thread border router, connects wirelessly to Wi-Fi
✓UK version: Heating and Hot Water buttons with LEDs
✓Free app features include room-by-room control, Quick Actions, per-room schedules and a Control Mode for your heating system type
✓Offline schedule stored on the device
✓Box includes wiring accessories and a cable
✓Install needs iOS 16.4 or Android 9.0

Pros & Cons

Pros

+ Acts as a Thread border router so no Bridge X is needed
+ Manual buttons still work when offline
+ Replaces a boiler programmer for hot water control
+ Zoning support

Cons

− No display
− Wiring at 230 V means some customers will want an installer
− For larger homes tado recommends an additional Bridge X per 100 m²
− Not compatible with V3+

Good to Know

The UK version has Heating and Hot Water buttons that still work manually if the receiver goes offline, and an offline schedule is stored on the device. It has no display, so it is controlled through the tado° app, and it acts as a Thread border router, so no Bridge X is needed. It runs on 230 VAC and wires to a system or combi boiler, so some people will want an installer to fit it. For larger homes, tado recommends an additional Bridge X per 100 square metres. tado says the Heating button gives a 30-minute boost for all rooms in the receiver’s zone, or turns heating off for 60 minutes if the heat is already on, and the Hot Water button heats water for 60 minutes before the app schedule resumes. Three Wi-Fi LEDs show signal strength, with one meaning weak.

tado° Services Worth Knowing About

✓tado° AI Assist subscription — The free tado° app covers remote control, Smart Schedule and Room Link. tado lists features such as Adaptive Heating, Geofencing, Preheat Before Arrival and Open Window Detection under the optional AI Assist subscription, which you buy in the app and can cancel at any time.
✓2-year tado° Premium Warranty — tado says its Premium Warranty runs for 24 months when you buy from tado.com or an authorised retail partner, with remote diagnostics and a rapid replacement if a hardware defect is confirmed. Products from eBay, Amazon Marketplace and other secondary sellers are not covered.
✓tado° Energy Savings Promise — For tado° X heating products bought on or after 2 September 2026, tado says you can return them within 12 months, after at least six months of active use, without showing energy consumption data or bills. You contact tado customer service via chat to arrange it, and tado says it applies whether you bought from tado or another online shop.

Setup & Installation

The Wireless Receiver X is wired in at the boiler, either in place of the existing one- or two-channel programmer or on a boiler that has no controls yet, and in tado’s UK kits it appears as the Programmer X with Hot Water Control. It runs on 230 V, and the app generates wiring steps once you choose your boiler or current programmer, with tado advising that wires sharing a terminal stay together and that the earth goes into the marked ground terminal on the UK unit. Where a room thermostat or wireless thermostat receiver is already fitted alongside a two-channel programmer, tado says it is bridged during installation so that tado° has full control of the heating. The receiver joins your Wi-Fi with its WPS button, a single pulsing Wi-Fi LED shows it is ready for the app, and because it works as a Thread border router no Bridge X is needed. tado also offers a booked professional installation with its UK wireless kit for anyone who would rather not handle the wiring.

Common Problems & Fixes

Running into issues? Our tado° troubleshooting guide covers step-by-step fixes for the common faults. Popular guides: offline, lights and buttons, won’t connect to Wi-Fi, wiring doesn’t match.

Who Should Buy It

Best for homes with a wireless thermostat, a hot water programmer or no room thermostat, which tado says usually need a Wireless Receiver X. See our starter kit guide.

Verdict

The Wireless Receiver X is the heart of the wireless tado° X kit: it wires to the boiler, gives hot water control, and doubles as a Thread border router.

As an affiliate, we may earn a commission from qualifying tado° purchases.

Need a hand with this?

If you are unsure about the thermostat wiring or the boiler connection, a heating engineer can fit it or find the fault. Any work on the boiler itself must be done by a Gas Safe registered engineer. You can compare up to 3 quotes from local heating engineers.

We may earn a commission if you request quotes through this link, at no cost to you.

⚠️ Important: This page is for guidance only. Heating systems vary. Turn off the power before touching any wiring, and if a radiator valve is seized, damaged or leaking, stop and contact a heating engineer. Follow tado°’s official guidance for your device.