Smart Temperature Sensor
tado° Wireless Temperature Sensor X Review

1st and 2nd gen | Thread + Matter | Works with Radiator X and Thermostat X

Overview

The Wireless Temperature Sensor X is a small room sensor that tells your tado° X system what the temperature is where you actually sit, rather than next to a radiator or on a hallway wall. It comes in two generations. The 1st gen runs on three AAA batteries, has a 49 x 30 mm LCD with three buttons and measures 100 x 100 x 21 mm. The 2nd gen is 17.8 mm thin with a built-in rechargeable battery, an LED matrix showing temperature and humidity, a light ring and a top button. Both are part of tado’s wireless starter kits, and both are sold on their own.

Ad: we earn commission if you buy through the price buttons on this page.

Check latest price

Subscription note: The tado° app works without a subscription. tado lists features such as Adaptive Heating, Geofencing and Open Window Detection under its optional AI Assist subscription, which you buy in the app and can cancel at any time.

Key Features

✓Adds an extra temperature reading to control one or several radiators in a room
✓Can act as the manual controller for every Radiator X in the room (2nd gen)
✓Wall mount, or a stand sold separately (2nd gen)
✓No wiring
✓Thread and Matter enabled
✓Works with all X products, including the 1st gen. Not compatible with V3+ or older
✓2nd gen top button gives one press to wake and a second press for a shortcut: resume schedule, boost heating or check humidity
✓Rechargeable over USB-C (2nd gen). The cable is not included

Pros & Cons

Pros

+ Reads the temperature where you choose to put it
+ Slim 2nd gen with a light ring and humidity display
+ Rechargeable 2nd gen with no batteries to buy
+ Fixes the over-reading problem when a Radiator X sits right next to a radiator
+ Part of the wireless starter kits

Cons

− Needs a Thread border router such as a Bridge X or Wireless Receiver X
− The 1st gen needs three AAA batteries
− The 2nd gen needs a USB-C cable you supply
− Stand sold separately
− Not compatible with V3+ or older tado°

Good to Know

The sensor gives your tado° X system a temperature reading from where you sit, rather than next to a radiator or on a hallway wall, and that reading can be used to control one or several radiators in a room. It needs no wiring, but it does need a Thread border router such as a Bridge X or Wireless Receiver X. The 1st gen runs on three AAA batteries, while the 2nd gen is rechargeable over USB-C with a cable you supply and can act as the manual controller for every Radiator X in the room. Both generations work with all tado° X products, but not with V3+ or older tado° systems. tado says to place it in the room you use most, about 1.5 metres above the floor and away from radiators, fireplaces, direct sunlight and draughts.

Which Version Should You Buy?

✓Wireless Temperature Sensor X (2nd gen) — Rechargeable, slimmer, with a light ring and humidity display. Check latest price
✓Wireless Temperature Sensor X (1st gen) — AAA-powered, with three buttons and an LCD. Check latest price

tado° Services Worth Knowing About

✓tado° AI Assist subscription — The free tado° app covers remote control, Smart Schedule and Room Link. tado lists features such as Adaptive Heating, Geofencing, Preheat Before Arrival and Open Window Detection under the optional AI Assist subscription, which you buy in the app and can cancel at any time.
✓2-year tado° Premium Warranty — tado says its Premium Warranty runs for 24 months when you buy from tado.com or an authorised retail partner, with remote diagnostics and a rapid replacement if a hardware defect is confirmed. Products from eBay, Amazon Marketplace and other secondary sellers are not covered.
✓tado° Energy Savings Promise — For tado° X heating products bought on or after 2 September 2026, tado says you can return them within 12 months, after at least six months of active use, without showing energy consumption data or bills. You contact tado customer service via chat to arrange it, and tado says it applies whether you bought from tado or another online shop.

Setup & Installation

The Wireless Temperature Sensor X needs no wiring and is added through the tado° app, which guides you through pairing it with the thermostat or radiator thermostats in that room, but it does rely on a Thread border router such as a Bridge X, Wireless Receiver X or Heat Pump Optimizer X. The 1st gen comes with its three AAA batteries, while tado recommends fully charging the 2nd gen before installation, which takes about four to five hours using a USB-C cable you supply. Both generations come with screws, wall plugs and sticky pads, so a screwdriver is only needed if you screw it to the wall, and tado also sells a separate Stand for placing it on a surface. Because cooler air sinks, tado suggests around 1.5 metres above the floor in the room you use most, away from radiators, fireplaces, televisions, direct sun and cold draughts from windows or doors.

Common Problems & Fixes

Running into issues? Our tado° troubleshooting guide covers step-by-step fixes for the common faults. Popular guides: won’t connect during setup, offline, restart and factory reset, best placement.

Who Should Buy It

Best for anyone choosing the wireless starter kit, anyone with a Radiator X in a large room or a room where the valve is badly placed, and heat pump owners replacing a deactivated room thermostat. Not sure you need one? Read our do you need a Wireless Temperature Sensor X guide.

Verdict

The Wireless Temperature Sensor X is a simple way to make a tado° X system respond to the temperature in the part of the room that matters. Choose the 2nd gen for the rechargeable design and humidity display, or the 1st gen if you prefer AAA batteries.

As an affiliate, we may earn a commission from qualifying tado° purchases.

Need a hand with this?

If you are unsure about the thermostat wiring or the boiler connection, a heating engineer can fit it or find the fault. Any work on the boiler itself must be done by a Gas Safe registered engineer. You can compare up to 3 quotes from local heating engineers.

We may earn a commission if you request quotes through this link, at no cost to you.

⚠️ Important: This page is for guidance only. Heating systems vary. Turn off the power before touching any wiring, and if a radiator valve is seized, damaged or leaking, stop and contact a heating engineer. Follow tado°’s official guidance for your device.